SCAL for eCraft machines

Discuss various cutting machines for SCAL
craftedge
Site Admin
Posts: 353
Joined: Tue Jul 05, 2011 10:34 pm

SCAL for eCraft machines

Post by craftedge »

We have a version of SCAL to work with the eCraft in beta testing right now.
If you are interesting in helping to test out the new version, please email us at
betatest@craftedge.com

and indicate your operating system and what firmware version is on your eCraft (version shown on the display on the eCraft right after you turn it on)

scrpbooklady
Posts: 356
Joined: Mon Apr 07, 2008 8:55 am
Location: SCAL2, SCAL1, XP

Re: SCAL for eCraft machines

Post by scrpbooklady »

Wish I had one - but I've been delaying any purchase decision until SCAL was compatible! I'll be watching for updates on this!

Butterfly
Posts: 1144
Joined: Wed May 05, 2010 5:01 am
Location: Paris,Ohio
Contact:

Re: SCAL for eCraft machines

Post by Butterfly »

Me too

Kiss PC good bye
Scrappin My Way Through
Going Where I Please and Pleasing Where I Go

Windows XP, Expression, SCAL 2.041, Inkscape 47
http://darliciouscreations.weebly.com/

richardcnc
Posts: 1
Joined: Fri Feb 04, 2011 4:05 am
Location: North Yorkshire, England, UK
Contact:

Re: SCAL for eCraft machines

Post by richardcnc »

I have an ecraft and am looking forward to testing the beta version, I have sent an email.
Richard

Richard Adams
North Yorkshire, England, UK
www.cutandcreativity.co.uk
Craft Demonstrator / Tutor

He**inwa
Posts: 60
Joined: Thu Apr 17, 2008 7:35 am

Re: SCAL for eCraft machines

Post by He**inwa »

Me too

Kiss PC good bye
^ ^ ^
That.
Particularly after the last few days.

And no mats!
JMO

imcindyc
Posts: 2
Joined: Thu Dec 02, 2010 5:30 am

Re: SCAL for eCraft machines

Post by imcindyc »

Do we have an ETA of when SCAL will be available to use with the eCraft?

pennsylvaniakate
Posts: 522
Joined: Sun Apr 26, 2009 7:28 am
Location: Pennsylvania - SCAL 1 & 2, Vista

Re: SCAL for eCraft machines

Post by pennsylvaniakate »

If you already have an Ecraft, you can contact Craft Edge about testing the Beta version.

Amanda_Nicole0315
Posts: 1
Joined: Mon Apr 11, 2011 6:17 am

Re: SCAL for eCraft machines

Post by Amanda_Nicole0315 »

ECRAFT the best easy to use and i save a lot on money all i need to buy is paper and nothing else. Fast and easy.

renees
Posts: 75
Joined: Sat Feb 19, 2011 9:40 am

Re: SCAL for eCraft machines

Post by renees »

I downloaded a trial version that allows the ecraft to work with SCAL but it cuts the lines through the project and does the whole purchase thing. So are we going to have to buy a new license to use SCAL on the Ecraft or just update the license we have now? If we have to purchase another copy of SCAL then when would be a good time to do that?
ReneeS

pennsylvaniakate
Posts: 522
Joined: Sun Apr 26, 2009 7:28 am
Location: Pennsylvania - SCAL 1 & 2, Vista

Re: SCAL for eCraft machines

Post by pennsylvaniakate »

If you contacted Craft Edge, and they sent you the Beta version to test, you should not have the watermark cuts or be prompted to purchase. You are helping them in testing the software to find improvements for a future release and need to be able to use the complete Beta version.

Post Reply