Craft Edge

Sure Cuts A Lot Forum
It is currently Wed Nov 14, 2018 8:21 am

All times are UTC - 8 hours




Post new topic Reply to topic  [ 24 posts ]  Go to page Previous  1, 2, 3
Author Message
PostPosted: Fri Apr 11, 2014 2:02 am 

Joined: Wed Dec 01, 2010 4:29 pm
Posts: 1964
Location: Sandy in PA (PC&MAC,Inkscape .48, SCAL2,eClips, eCAL)
Can you revert back to the last version of eCAL and see if it still does the same thing? That might possibly isolate the issue as being either software or the machine.

_________________
Sandy in PA


Top
 Profile  
 
PostPosted: Thu Jul 24, 2014 3:49 pm 

Joined: Wed Jul 23, 2014 7:21 pm
Posts: 1
I too, am having all the issues with the eclips not cutting all the way to the right. I am running windows 8.1 and have reinstalled the driver (special instructions). I upgraded to the latest version last night thinking that may be the problem. It has not fixed anything. I have reset the machine to factory. Nothing. This machine is over a year old already. These issues are quite frustrating.

Any other suggestions? I also have orders waiting!!


Top
 Profile  
 
PostPosted: Sun Jul 27, 2014 2:50 pm 

Joined: Wed Apr 09, 2014 5:07 am
Posts: 4
I called Sizzix again and told them I was not getting any response from the makers of the software company. I had 2 Eclips machines, one was under warranty (less than a year old) and they said it sounded like the laser was bad due to the problems I described in my earlier post. They replaced it.
It's interesting because this was the second time that particular machine had to be replaced and the Sizzix rep said they used to replace them with refurbished machines but now they are replacing them with new ones. Hmm. The other machine was 8 months past the warranty so they wouldn't do anything about it. The symptoms were cutting wonky shapes all over the mat and then stalling led to the diagnosis of a bad mother board. :-(. What a sad day having to feed it to the dumpster.

So far the replaced machine is cutting well with the upgraded software.


Top
 Profile  
 
PostPosted: Sun Oct 04, 2015 2:46 pm 

Joined: Fri Sep 04, 2009 6:32 pm
Posts: 6
WELL Mine went Bonkers today This is the second one I have had replaced in 2013 it acts like its got rabies and chews it up and then spits it out and then starts cutting all over the place.. I got to say I have had it for 2 years and I LOVE LOVE It but now I don't know what to do and now I got all these cartridges (44) as a matter of fact I could just cry..
It will start cuttin and then stop spit out mat and then just start cutting crazy.. The it might start to cut something and then it just stops right in the middle and shuts down..
I have replaced cords
I made sure ecal is up to date
I used a new mat
I did the x and then the laser light
I tried my cartridges and it will not even do that
I cleaned the sensor
I cleaned the blade I mashed those 2 red things on the side
NOTHING..
OOOO I even tried Hooking it up to another computer..
I have emailed Sizzix Hoping i can send it to get repaired


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 24 posts ]  Go to page Previous  1, 2, 3

All times are UTC - 8 hours


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group