Craft Edge

Sure Cuts A Lot Forum
It is currently Sun Dec 09, 2018 8:06 pm

All times are UTC - 8 hours




Post new topic Reply to topic  [ 4 posts ] 
Author Message
PostPosted: Mon Dec 03, 2018 7:06 pm 

Joined: Mon Dec 03, 2018 6:51 pm
Posts: 2
Hello,

Newbie here, I couldn't find any answer elsewhere here.

I am cutting some curved shapes out of basically card stock with SCUT3 and an eCraft cutter, and I am having trouble with "tabs" as eCraft calls them, or "gaps" in the lines as they seem to be referred to in SCUT. More generally, call it "perforations". i.e. I don't want pieces to fall out and there is no mat or anything holding it together. Hence little tabs spaced around.

Details:

- Shape loaded up and edge traced. Then I convert the trace to a dashed line from solid, say 300 with 3 gap.
- set eCraft to zero tabs just in case.
- load and cut.

However, it's not cutting the 300x3. It seems to be doing its own thing, which is shorter cuts and more tabs, regardless of what I set the line parameters to. Put another way, the gaps don't match what is showing in SCUT.

If I set it to a continuous line though, it cuts those just fine (and pieces fall out of course).

Am I missing something obvious? I looked at every possible feature I could find.

Thanks kindly in advance.


Top
 Profile  
 
PostPosted: Tue Dec 04, 2018 7:03 am 

Joined: Mon May 09, 2011 7:01 am
Posts: 438
It's been years since I tested an eCraft for Janome's consideration and I was testing from eCraft's own software. So, I'm not much help. However, I did some research for you and found an eCraft blog that was highly recommended and it appears the owner also used SCUT3. Maybe try searching articles there and even contacting the owner of the blog to see if she still actively helps her readers:

http://purplepaperparadise.blogspot.com/

_________________
Sandy McCauley
Manager of Customer Relations and Education for KNK USA
Owner of http://www.iloveknk.com/


Top
 Profile  
 
PostPosted: Tue Dec 04, 2018 3:06 pm 

Joined: Mon Dec 03, 2018 6:51 pm
Posts: 2
Update:

I did some more tests, with the following results:

-If I leave the lines as continuous, it seems to be fine.

-If I change any of the cuts to dashed lines, it seems to insert a bunch of garbage, which seems to be consistent with "watermarking". In particular, it seems to put the tabs where I want them, but it also adds a bunch more, which I believe is what was confusing me in my original post. It also adds a few random slices across parts of the piece.

- Just to make sure it wasn't something with the file I'm trying to cut, I exported it to .png, created a new project, and re-imported it as an image to trace. Same results with solid vs. perforated cutting tests, except the "garbage" was different.

The later would be understandable for an unregistered copy, but this copy is registered as far as I can tell. i.e. I can go to "about" under the help tab and it gives me the previous owner's name and serial number.

One thing might be that there are somehow multiple copies that are/were on various PC's that are all under the same licence key somehow, so the license server it telling the software to fail? It'd be nice if that that the software told you if that was the case...

Any ideas? I emailed support but they talk about 3 days response time.

Maybe I need to spring for the $59 to buy SCUT5.


Top
 Profile  
 
PostPosted: Wed Dec 05, 2018 6:37 am 

Joined: Mon May 09, 2011 7:01 am
Posts: 438
If the issue was tied to registration, then the continuous line cut would not be fine... you would be getting watermark cuts through the shape.

Again, because this forum is not very active, I urge you to find an eCraft forum, Yahoo group, Facebook group or perhaps the owner of that blog I recommended so that someone who HAS used SCAL3 can help with this issue, based on their knowledge of using the software with an eCraft. If you DO get it working, I highly recommend SCAL5 because it is loaded with designing functionality and it's a great price for what you get.

_________________
Sandy McCauley
Manager of Customer Relations and Education for KNK USA
Owner of http://www.iloveknk.com/


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 4 posts ] 

All times are UTC - 8 hours


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group