Craft Edge
http://forum.surecutsalot.com/

Important Announcement: SCAL 1 and 2
http://forum.surecutsalot.com/viewtopic.php?f=81&t=21085
Page 15 of 16

Author:  mariehale1021 [ Sun Dec 02, 2012 12:50 pm ]
Post subject:  Re: Important Announcement: SCAL 1 and 2

ok I have scal 2 and want to upgrade to scal3 and i saw somewhere it is free to upgrade -BUT if i upfrade will scal 2 no longer work?

Author:  gj1 [ Sun Dec 02, 2012 2:11 pm ]
Post subject:  Re: Important Announcement: SCAL 1 and 2

http://craftedge.com/purchase/craftedge ... grade3.php

http://craftedge.com/products/products_scal.html


The install and operate separately. You can still use version 2.

Author:  shazzy103 [ Thu Apr 18, 2013 10:49 pm ]
Post subject:  Re: Important Announcement: SCAL 1 and 2

I wish I had seen this before getting rid of my old computer ... I am so upset I have lost the scal software and the new one don't work with the cricut, if I had have known I would have saved the scal file before dumping the old computer

Author:  Crazygurl [ Fri May 10, 2013 8:06 am ]
Post subject:  Re: Important Announcement: SCAL 1 and 2

Is there any way I can put my firmware version back to its original state on my cricut personal? I updated my firmware and its v1.45 and my scal2 wont work in it?Thanks in advance.

Author:  lilminney [ Fri Jul 19, 2013 8:43 pm ]
Post subject:  Re: Important Announcement: SCAL 1 and 2

Sad sad sad but thanks for the announcement. I'm wondering if it needs to be reinstalled about activation?

Author:  adrianwfar [ Fri Nov 08, 2013 1:46 pm ]
Post subject:  Re: Important Announcement: SCAL 1 and 2

I did the firmware update, so how could I go back again! :oops: Thanks
Also, I see the Scal doesn't have a cricut in cutters.

Author:  Sweetness4713 [ Fri Nov 08, 2013 6:32 pm ]
Post subject:  Re: Important Announcement: SCAL 1 and 2

After provocraft threatened lawsuits craftedge no longer support past scal2 for cricut.

Author:  rmmahrens [ Sat Jun 21, 2014 1:26 pm ]
Post subject:  Re: Important Announcement: SCAL 1 and 2

Crazygurl wrote:
Is there any way I can put my firmware version back to its original state on my cricut personal? I updated my firmware and its v1.45 and my scal2 wont work in it?Thanks in advance.


Did you figure out a way to bring the firmware back? I'm also looking to do this.

Author:  papasue [ Sun Jun 22, 2014 5:25 am ]
Post subject:  Re: Important Announcement: SCAL 1 and 2

I think your only recourse is to contact Provocraft support to see if the will help you downgrade the firmware. Ensure that you understand what the downgrade will do to others programs you have from them.

Provocraft.com

Author:  talanhart [ Mon Jun 23, 2014 4:48 am ]
Post subject:  Re: Important Announcement: SCAL 1 and 2

There is a way to reverse your firmware back to an older version. It involves replacing one file in the updater program. I have the instructions here on the board. It will take awhile to find, but it can be done.

Page 15 of 16 All times are UTC - 8 hours
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/