Craft Edge

Sure Cuts A Lot Forum
It is currently Sun Sep 15, 2019 8:28 pm

All times are UTC - 8 hours




Post new topic Reply to topic  [ 18 posts ]  Go to page Previous  1, 2
Author Message
PostPosted: Sun Jul 01, 2012 8:54 am 

Joined: Sat Jun 16, 2012 4:36 pm
Posts: 287
Oooo.. I spotted a slight error..

I will adjust and upload again, sorry about that..

_________________
Software: Windows 7 (64 bit) - SCAL 3 - Inkscape - Illustrator CS4 - Signcut Pro
Cutter 1: Blackcat Cougar 24" connected via Keyspan/ serial
Cutter 2: Phoenix Silver Bullet Pro 24" connected via Keyspan/ serial


Top
 Profile  
 
PostPosted: Sun Jul 01, 2012 9:08 am 

Joined: Sat Jun 16, 2012 4:36 pm
Posts: 287
here they are, just SVG's, I figure its easy enough to import them ;)

Attachment:
invite-flaps-5 x 7 - rounded.svg [3.18 KiB]
Downloaded 221 times


Attachment:
invite-flaps-5 x 7.svg [2.74 KiB]
Downloaded 221 times


The little corner cutouts were 90 degrees on the original which would have likely stuck out a bit after folding, I just made them a bit greater than 90 degrees so it will sit better when folded.

Enjoy

_________________
Software: Windows 7 (64 bit) - SCAL 3 - Inkscape - Illustrator CS4 - Signcut Pro
Cutter 1: Blackcat Cougar 24" connected via Keyspan/ serial
Cutter 2: Phoenix Silver Bullet Pro 24" connected via Keyspan/ serial


Top
 Profile  
 
PostPosted: Sun Jul 01, 2012 12:48 pm 

Joined: Fri Jun 29, 2012 8:10 pm
Posts: 7
Wow! Thank you SOOO much! it looks fabulous. I am so impressed with your talent and your willingness to share it! :)


Top
 Profile  
 
PostPosted: Sun Jul 01, 2012 1:31 pm 

Joined: Sat Jun 16, 2012 4:36 pm
Posts: 287
rmcleish wrote:
Wow! Thank you SOOO much! it looks fabulous. I am so impressed with your talent and your willingness to share it! :)

You are very welcome :)

If you use it don't forget to share a picture or two ;)

_________________
Software: Windows 7 (64 bit) - SCAL 3 - Inkscape - Illustrator CS4 - Signcut Pro
Cutter 1: Blackcat Cougar 24" connected via Keyspan/ serial
Cutter 2: Phoenix Silver Bullet Pro 24" connected via Keyspan/ serial


Top
 Profile  
 
PostPosted: Tue Feb 26, 2013 9:08 am 

Joined: Fri Nov 13, 2009 5:58 am
Posts: 209
QUESTION on the envelopes with flaps - in preview it appears it is going to cut 2 rectangles basically - I tried to weld them together and preview again and it looks the same - how can I get this to not cut out the inside lines and just the outline of the envelope - I assume you score the inside lines to fold --- am I having a brain freeze or what ?? Thanks for any help

Regards,
Cathy


Top
 Profile  
 
PostPosted: Tue Feb 26, 2013 9:49 am 

Joined: Fri Jun 29, 2012 8:10 pm
Posts: 7
wvcathy wrote:
QUESTION on the envelopes with flaps - in preview it appears it is going to cut 2 rectangles basically - I tried to weld them together and preview again and it looks the same - how can I get this to not cut out the inside lines and just the outline of the envelope - I assume you score the inside lines to fold --- am I having a brain freeze or what ?? Thanks for any help

Regards,
Cathy



I just go to OBJECT and the UNGROUP and then would delete the inside rectangle, then cut.


Top
 Profile  
 
PostPosted: Tue Feb 26, 2013 10:02 am 

Joined: Fri Nov 13, 2009 5:58 am
Posts: 209
I think I have the envelope problem fixed BUT now is there a way to put 2 small holes on each of the Larger flaps - so they will line up so you could run some twine or something thru it - hope this makes sense - but I would like to put 2 eyelets in each flap and run twine thru it - for a rustic type wedding invite

I have tried several times to line these up just not having luck and I am hoping some of you great people out there know of a simple way to do this

Thanks,
Cathy


Top
 Profile  
 
PostPosted: Sat Jun 28, 2014 12:18 am 

Joined: Fri Jun 27, 2014 11:42 pm
Posts: 1
I am looking to make invitation card for my wedding party venue nyc. Please give me the best ideas for design and quotation of cards.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 18 posts ]  Go to page Previous  1, 2

All times are UTC - 8 hours


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Group