Craft Edge

Sure Cuts A Lot Forum
It is currently Fri Dec 15, 2017 4:17 am

All times are UTC - 8 hours




Post new topic Reply to topic  [ 157 posts ]  Go to page Previous  1 ... 10, 11, 12, 13, 14, 15, 16  Next
Author Message
PostPosted: Mon Jan 09, 2012 8:25 am 

Joined: Sat Jan 01, 2011 1:09 pm
Posts: 24
I thought I had backed up my SCAL2, but something happen to it on the flash drive. Could someone tell me what to do, I purchased SCAL2 and computer crashed, now I can't use my cricut for I don't have SCAL2 and I have all my serial numbers, activation code and order number from when I purchased it...HELP PLEASE!!!


Top
 Profile  
 
PostPosted: Mon Jan 09, 2012 10:17 am 

Joined: Wed Dec 01, 2010 4:29 pm
Posts: 1964
Location: Sandy in PA (PC&MAC,Inkscape .48, SCAL2,eClips, eCAL)
Go to this link and request assistance here.

http://www.craftedge.com/support/lostsw.php

_________________
Sandy in PA


Top
 Profile  
 
PostPosted: Mon Jan 30, 2012 3:28 pm 

Joined: Mon Jan 30, 2012 3:17 pm
Posts: 1
Can anyone help me? I'm am getting very frustrated and I need to make some cuts to finish a project I'm doing for a swap. I have SCAL2 and a Cricut expressions my firmware is 2.3X I got an SVG file of the liberty bell and am just trying to cut the bell part and every time I hit cut it goes through all the motions starts to cut a 1/2 inch cut and shuts off turns back on and unloads the paper and turns off SCAL. I am so frustrated!! I love using SCAL but I'm about ready to throw the computer and the cricut!! HELP!!! :o :cry:
Cheryl


Top
 Profile  
 
PostPosted: Sat Feb 11, 2012 7:30 pm 

Joined: Sat Feb 11, 2012 7:11 pm
Posts: 2
hi people im a new scal user but i recieving an error. every time im ready to cut it says im not connected.
i updated my firmware, and same problem . HELP. :cry:


Top
 Profile  
 
PostPosted: Sun Feb 12, 2012 6:29 am 

Joined: Wed Dec 01, 2010 4:29 pm
Posts: 1964
Location: Sandy in PA (PC&MAC,Inkscape .48, SCAL2,eClips, eCAL)
Try shutting everything down (computer and cutter). Then to a brand new restart of computer, then turn on Cricut. This has been an issue in the past and the problem may be as simple as that. Others have had to replace their USB/printer cable from machine to computer. If this doesn't work, check back.

_________________
Sandy in PA


Top
 Profile  
 
PostPosted: Tue Feb 14, 2012 5:13 am 

Joined: Sat Feb 11, 2012 7:11 pm
Posts: 2
thanks bud will try these

but will it work with my Expression 2? :|


Top
 Profile  
 
PostPosted: Wed Feb 15, 2012 7:33 am 

Joined: Mon Sep 28, 2009 3:06 am
Posts: 363
Location: Newport News, VA, USA; SCAL 2.044-Expression; SCAL 3-Cameo; Mac; Inkscape 0.48; GIMP 2.6
flowclee wrote:
thanks bud will try these

but will it work with my Expression 2? :|

No. No third-party software will work with the Expression 2. If you want to use software other than Provo Craft's own Craft Room, then return the Expression 2 and buy a different machine.

The Sizzix eclips is very nice, has cartridges much like the Cricut, and works with a couple of different software products.

- Jasen.


Top
 Profile  
 
PostPosted: Mon Jun 11, 2012 12:24 am 

Joined: Tue May 29, 2012 6:33 pm
Posts: 2
I've been having issues as well, tried running XP SP2 mode but still freezing when trying to cut. Was reluctant to do any further upgrades as I have a cricut.

However, in desperation I have just been to the software page http://www.craftedge.com/support/lostsw.php entered my serial number of SCAL2 (they will email to you if you don't have it) and it downloaded the most recent version of SCAL2 (2.044).

Make sure you uninstall the latest version BEFORE you install the new one. The new one once installed automatically runs in XP SP2 compatability mode and is automatically activated if you do this.

I have shut down the software twice and seems to be working fine with the Cricut now. Hopefully when I turn on again tomorrow it will still be all good.


Top
 Profile  
 
PostPosted: Mon Jun 11, 2012 5:45 pm 

Joined: Mon Oct 12, 2009 5:01 am
Posts: 4465
Hope all is good when you open the program again.

_________________
My pictures and files are available for a limited time only.


Top
 Profile  
 
PostPosted: Thu Jun 14, 2012 7:48 am 

Joined: Thu Jun 14, 2012 6:41 am
Posts: 4
I lost my SCAL cd, I went to the link. Downloaded put in my S#, now it comes up SCAL 3. It's not compatible with my cricut, now what do I do? Please help me!!!


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 157 posts ]  Go to page Previous  1 ... 10, 11, 12, 13, 14, 15, 16  Next

All times are UTC - 8 hours


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Group